Jules Verne demonstrates flawless Collision Avoidance Maneuver

The in-flight Collision Avoidance Manoeuvre, or CAM, demonstration was necessary to prove that the spacecraft could reliably move away from the ISS in case of any problems during the final rendezvous and docking with the International Space Station. Upon detection of a critical failure or an unsafe situation, the spacecraft's Monitoring and Safing Unit (MSU) is designed to isolate the ATV's nominal systems and issue a CAM command.

"It went perfectly - the MSU commanded ATV exactly as expected. After that, we had a perfect recovery of the spacecraft, from sun-pointing safe mode, and we reset the on-board computers. ATV is back in cruise mode," said Alberto Novelli, ESA's Mission Director at the ATV Control Centre in Toulouse, France.

The complex procedure involved shutting down all of the normal control systems and placing the spacecraft into 'last-chance' survival mode. After the manoeuvre was positively demonstrated and confirmed, controllers implemented a lengthy 'exit-from-survival' recovery process that brought all systems back into nominal operation.

"The performance was absolutely flawless. We know now that it is completely safe for us to go to the Station because we always have an independent way to get away from it. This demonstrates that our back-up 'spacecraft within a spacecraft' works perfectly - it's good to have this tool in our back pocket," said John Ellwood, ESA's ATV Project Manager.

An enhanced team of some 60 mission controllers from ESA and French space agency CNES watched this morning's test intently from the ATV Control Centre. If any problems had occurred during survival mode, it would have been very difficult to recover the spacecraft.

"This independent mode relies on separate computers, separate software, separate batteries, separate trajectory monitoring sensors and separate thrusters. The only item shared with the ATV's main system is propellant," explained ESA astronaut Jean-François Clervoy, senior advisor to the ATV project.

The test was conducted with ATV orbiting well away from the ISS, and included a 200-second thruster burn, which took place as the spacecraft passed over northern Africa. A final orbit determination will be done later today.

The CAM demonstration was also monitored closely by ESA's ISS partners, with NASA operations personnel seated on console in the ATV Control Centre. The US and Russian ISS control centres and ESA's Columbus Control Centre also monitored the test. One important result of the demonstration was to prove to the partners that the CAM functionality was reliable and could assure the safety of the Station and crew members. The CAM demonstration results are now being analysed by the ISS partners.

Additional demonstrations of Jules Verne's functionality are scheduled later in the month, with actual rendezvous and docking planned for 3 April 2008.

Source: European Space Agency

ATV Jules Verne automated ship docks to the ISS
ATV Jules Verne, the European Space Agency’s first resupply and reboost vehicle, has successfully performed a fully automated docking with the International Space Station (ISS). This docking marks the beginning of Jules Verne’s main servicing mission to deliver cargo, propellant, water, oxygen and propulsion capacity to the Station, as well as ESA’s entry into the restricted club of the partners able to access the orbital facility by their own means.
Successful manoeuvres position Jules Verne ATV for crucial tests
Jules Verne ATV successfully performed two boosts today, bringing the spacecraft to an altitude of 303 km – half-way between the insertion orbit reached after last Sunday's launch and the orbit of the International Space Station.
Jules Verne boosts ISS orbit
ESA's Jules Verne ATV was used for the first time early this morning to raise the orbit of the International Space Station. A 740-second burn of the Automated Transfer Vehicle's main engines successfully lifted the altitude of the 280-tonne Station by around 4.5 km to a height of 342 km above the Earth's surface.
Jules Verne ATV given 'go' for docking
Jules Verne was today formally cleared to proceed with the first ISS docking attempt, scheduled for 3 April 2008 at 16:41 CEST (14:41 UT). The official go-ahead came from the International Space Station Mission Management Team (IMMT) after two flawless demonstration days in which Jules Verne proved its operational capabilities.
Impressive dress-rehearsal for Jules Verne ATV
Jules Verne ATV today approached the International Space Station to within 11 m of the docking port on the Russian Zvezda module. The approach was part of a second ATV demonstration day which clears the way for the first rendezvous and docking attempt on 3 April.
Follow live Jules Verne ATV's first attempt to dock with the International Space Station
After several days spent in a parking orbit 2000 km ahead of the ISS, Jules Verne ATV is now ready to join up with the International Space Station. This first docking attempt can be followed live on 3 April 2008 from 15:30 CEST onwards from one of the European participating centres.
Jules Verne reaches 'parking' orbit
Jules Verne ATV has today reached a parking position 2000 km ahead of the International Space Station. Europe's ISS re-supply spacecraft will wait at this holding point for the completion of the STS-123 Space Shuttle mission before proceeding with the first of two rendezvous demonstration days.
Artemis provides communications for Jules Verne ATV
ESA's Artemis data relay satellite, controlled from Fucino (Italy) and with its mission control centre and Earth terminal located at Redu (Belgium), is providing communications between the Jules Verne ATV and the ATV Control Centre in Toulouse (France).

Jules Verne demonstrates flawless Collision Avoidance Maneuver

Related stories:

News discussion: