Fake diamonds help jet engines take the heat

Ohio State University engineers are developing a technology to coat jet engine turbine blades with zirconium dioxide -- commonly called zirconia, the stuff of synthetic diamonds -- to combat high-temperature corrosion.

The zirconia chemically converts sand and other corrosive particles that build up on the blade into a new, protective outer coating. In effect, the surface of the engine blade constantly renews itself.

Ultimately, the technology could enable manufacturers to use new kinds of heat-resistant materials in engine blades, so that engines will be able to run hotter and more efficiently.

Nitin Padture, professor of materials science and engineering at Ohio State, said that he had military aircraft in mind when he began the project. He was then a professor at the University of Connecticut.

“In the desert, sand is sucked into the engines during takeoffs and landings, and then you have dust storms,” he said. “But even commercial aircraft and power turbines encounter small bits of sand or other particles, and those particles damage turbine blades.”

Jet engines operate at thousands of degrees Fahrenheit, and blades in the most advanced engines are coated with a thin layer of temperature-resistant, thermally-insulating ceramic to protect the metal blades. The coating -- referred to as a thermal-barrier coating -- is designed like an accordion to expand and contract with the metal.

The problem: When sand hits the hot engine blade it melts -- and becomes glass.

“Molten glass is one of the nastiest substances around. It will dissolve anything,” Padture said.

The hot glass chews into the ceramic coating. But the real damage happens after the engine cools, and the glass solidifies into an inflexible glaze on top of the ceramic. When the engine heats up again and the metal blades expand, the ceramic coating can’t expand, because the glaze has locked it in place. The ceramic breaks off, shortening the life of the engine blades.

In a recent issue of the journal Acta Materialia, Padture and his colleagues described how the new coating forces the glass to absorb chemicals that will convert it into a harmless -- and even helpful -- ceramic.

The key, Padture said, is that the coating contains aluminum and titanium atoms hidden inside zirconia crystals. When the glass consumes the zirconia, it also consumes the aluminum and titanium. Once the glass accumulates enough of these elements, it changes from a molten material into a stable crystal, and it stops eating the ceramic.

“The glass literally becomes a new ceramic coating on top of the old one. Then, when new glass comes in, the same thing will happen again. It’s like it’s constantly renewing the coating on the surface of the turbine,” Padture said.

Padture’s former university has applied for a patent on the technique that he devised for embedding the aluminum and titanium into the zirconia. He’s partnering with Inframat Corp., a nanotechnology company in Connecticut, to further develop the technology.

Padture stressed that the technology is in its infancy. He has yet to apply the coatings to complex shapes, and cost is a barrier as well: the process is energy-consuming.

But if that cost eventually came down and the technology matured, the payoff could be hotter engines that burn fuel more efficiently and create less pollution. Manufacturers would be able to use more sophisticated ceramics that boost the heat-resistance of engines. Eventually, technology could go beyond aircraft and power-generator turbines and extend to automobiles as well, Padture said.

Source: Ohio State University

Related stories:

Coating copies microscopic biological surfaces
Someday, your car might have the metallic finish of some insects or the deep black of a butterfly's wing, and the reflectors might be patterned on the nanostructure of a fly's eyes, according to Penn State researchers who have developed a method to rapidly and inexpensively copy biological surface structures.
Sony Unveils the Worlds first 24.6-megapixel DSLR Camera
Sony's DSLR-A900 will be available in November, along with related accessories; online pre-orders start on September 10. The DSLR-A900 is designed to deliver ultra-fine picture quality with its stunning 24.6 megapixel, 35 mm full-frame CMOS sensor and fast image processing.
Butterfly wings may help scientists better understand photonic crystals
As technology moves forward, many scientists are looking to nature to find inspiration for the development of advanced materials that can have a variety of practical applications.
Candy-coating keeps proteins sweet
Sugar-frosting isn’t just for livening up boring bran flakes; it can also preserve important therapeutic proteins. Researchers at the National Institute of Standards and Technology have developed a fast, inexpensive and effective method for evaluating the sugars pharmaceutical companies use to stabilize protein-drugs for storage at room temperature. The group presented their findings at the 236th American Chemical Society National Meeting and Exposition.
Nothing stops an expert in the art of living
There are few things more irritating than a fly buzzing around the house. South African's have an unconventional solution to the problem. They hang up a bunch of Roridula gorgonias leaves. Attracted to the shiny adhesive droplets on the leaf's hairs, the hapless pest is soon trapped by the natural flypaper.
Researchers redefine ultrathin display process
(PhysOrg.com) -- The Flexible Display Center at Arizona State University has developed a new process for manufacturing high-performance flexible displays on transparent plastic.
Artificial Lotus Effect: Carbon nanotubes with nanoscopic paraffin coating form superhydrophobic, self-cleaning surfaces
Never wash your car again? Never clean your windows? These may well become reality if it becomes possible to produce the right coatings—coatings that imitate the self-cleaning effect of the lotus blossom.
NASA Scientists Pioneer Method for Making Giant Lunar Telescopes
Scientists working at NASA’s Goddard Space Flight Center in Greenbelt, Md., have concocted an innovative recipe for giant telescope mirrors on the Moon. To make a mirror that dwarfs anything on Earth, just take a little bit of carbon, throw in some epoxy, and add lots of lunar dust.

News discussion:

Physics news