MIT Creates New Material For Fuel Cells, Increases Power Output By 50 Percent

MIT engineers have improved the power output of one type of fuel cell by more than 50 percent through technology that could help these environmentally friendly energy storage devices find a much broader market, particularly in portable electronics.

The new material key to the work is also considerably less expensive than its conventional industrial counterpart, among other advantages.

“Our goal is to replace traditional fuel-cell membranes with these cost-effective, highly tunable and better-performing materials,” said Paula T. Hammond, Bayer Professor of Chemical Engineering and leader of the research team. She noted that the new material also has potential for use in other electrochemical systems such as batteries.

The work was reported in a recent issue of Advanced Materials by Hammond, Avni A. Argun and J. Nathan Ashcraft. Argun is a postdoctoral associate in chemical engineering; Ashcraft is a graduate student in the same department.

Like a battery, a fuel cell has three principal parts: two electrodes (a cathode and anode) separated by an electrolyte. Chemical reactions at the electrodes produce an electronic current that can be made to flow through an appliance connected to the battery or fuel cell. The principal difference between the two" Fuel cells get their energy from an external source of hydrogen fuel, while conventional batteries draw from a finite source in a contained system.

The MIT team focused on direct methanol fuel cells (DMFCs), in which the methanol is directly used as the fuel and reforming of alcohol down to hydrogen is not required. Such a fuel cell is attractive because the only waste products are water and carbon dioxide (the latter produced in small quantities). Also, because methanol is a liquid, it is easier to store and transport than hydrogen gas, and is safer (it won't explode). Methanol also has a high energy density-a little goes a long way, making it especially interesting for portable devices.

The DMFCs currently on the market, however, have limitations. For example, the material currently used for the electrolyte sandwiched between the electrodes is expensive. Even more important: that material, known as Nafion, is permeable to methanol, allowing some of the fuel to seep across the center of the fuel cell. Among other disadvantages, this wastes fuel-and lowers the efficiency of the cell-because the fuel isn't available for the reactions that generate electricity.

Using a relatively new technique known as layer-by-layer assembly, the MIT researchers created an alternative to Nafion. “We were able to tune the structure of [our] film a few nanometers at a time,” Hammond said, getting around some of the problems associated with other approaches. The result is a thin film that is two orders of magnitude less permeable to methanol but compares favorably to Nafion in proton conductivity.

To test their creation, the engineers coated a Nafion membrane with the new film and incorporated the whole into a direct methanol fuel cell. The result was an increase in power output of more than 50 percent.

The team is now exploring whether the new film could be used by itself, completely replacing Nafion. To that end, they have been generating thin films that stand alone, with a consistency much like plastic wrap.

This work was supported by the DuPont-MIT Alliance through 2007. It is currently supported by the National Science Foundation.

Source: Massachusetts Institute of Technology

Related stories:

Sharp Achieves the World’s Highest Power Density for Direct Methanol Fuel Cells
Sharp Corp. has achieved the world's highest power density, 0.3W/cc, for direct methanol fuel cells (DMFC) for mobile equipment. This new technology enables efficient power generation from a small cell volume. The use of this technology can make it possible to develop fuel cells that have almost the same volume but a longer continuous-use lifespan than lithium-ion batteries, which are the main type currently in use.
Fuel cells: distant dream, but burning with promise
Some day, fuel cells may power your car and exhaust only water and perhaps carbon dioxide. More efficient and cleaner than an internal combustion engine, their emissions will be much lower. They may also run your home without the energy loss of power lines, or even power your laptop or cell phone. But not today or even tomorrow.
Power from Formic Acid
One of the central challenges of our time is the supply of enough environmentally friendly and resource-efficient energy to our society. In this context, hydrogen technology has taken on increased importance.
Chemical Engineer Discovers Way of Increasing Battery Life with Environmentally Friendly Fuel Cells
A Drexel University chemical engineering professor Yossef Elabd is exploring a way to increase battery life with an environmentally friendly alternative. Consumer demands are requiring lithium-ion batteries currently used to power devices such as cell phones and laptops to increase their efficiency and reduce environmental impact.
Working toward new energy with electrochemistry
In an effort to develop alternative energy sources such as fuel cells and solar fuel from “artificial” photosynthesis, scientists at the U.S. Department of Energy’s Brookhaven National Laboratory are taking a detailed look at electrons – the particles that set almost all chemical processes in motion.
Ceramic tubes could cut greenhouse gas emissions from power stations
Greenhouse gas emissions from power stations could be cut to almost zero by controlling the combustion process with tiny tubes made from an advanced ceramic material, claim engineers today.
Novel sugar-to-hydrogen technology promises transportation fuel independence
The hydrogen economy is not a futuristic concept. The U.S. Department of Energy's 2006 Advance Energy Initiative calls for competitive ethanol from plant sources by 2012 and a good selection of hydrogen-powered fuel cell vehicles by 2020.
Running on Microbes
What’s cleaner than coal, as renewable as solar energy and as ingenious as any of the cutting-edge alternative energy sources now being proposed for cars? The answer is microbe power, and if a USC team’s efforts to harness its electrical punch succeed, it may one day find uses in applications both big and small.

News discussion:

Physics news