Self-repairing materials

Will the day come when cracks in buildings close up without external help and before they get to the stage where they cause damage to the component? This might appear utopia, but it already occurs in nature. When a person suffers a minor wound, the human body reacts to close the opening, sending the blood platelets needed to the affected area – and with no need in many cases for any external coagulant substance to be employed.

This reaction of nature to damage suffered was the starting point for the development of self-repairing polymer materials with the capacity of recovering a good part of the properties lost and with no or with minimal external help. In the case of ceramics or metallic materials, progress is much slower, being limited to initial steps.

There are currently two notable self-repairing technologies in polymer materials: adhesives and thermal encapsulation.

As the name suggests, the first of these involves a series of "stores" of adhesive found distributed in the most homogenous manner possible throughout the material, so that when the crack reaches one of these nodes the adhesive is secreted, together with a catalyst, and the crack is closed and the material polymerised.

There are two variants within this line of technology, depending on whether adhesive-containing microcapsules or tubes filled with adhesive are employed.

INASMET-Tecnalia has worked on this line in a project undertaken for the AIRBUS, having managed to produce a series of microcapsules and distribute them in a polymeric resin. This was a fundamental step to finding out the difficulties that might arise in the encapsulation process.

The second method, developed by Bristol University, is a project for the ESA, is very similar. The difference lies in the use of tubes rather than microcapsules filled with adhesive.

The thermal method uses a different repair methodology. The material, developed by the University of Sheffield, is a polymeric matrix compound, reinforced with carbon fibres. The polymer matriz, in turn, is made of a solid solution of a thermoplastic polymer and another thermostable polymer.

The only restriction of the thermostable material is that it has to be suitable for incorporating these reinforcment fibres into it. The thermoplastic material has greater limitations, limiting it chances of being chosen for use, being highly dependant on the thermostable material used. In this case, when damage is detected, repair is carried out by heating the material with some device incorporated into it.

This heating is capable of raising the temperature above that of the fusion of the thermoplastic material which, as a result, melts and flows into the damaged areas so that the cracks are sealed and the component restored to its former condition. INASMET-Tecnalia has also worked in this field within the framework of the aforementioned project.

It should be underlined that the development of self-repairing materials is still at initial stages and there is a long way to go yet before reaching the desired goal. Nevertheless, the results obtained are encouraging.

Apart from participation in this project, INASMET-Tecnalia is working on a number of research lines related to the growing demand that is anticipated for self-repairing materials.

Source: Elhuyar Fundazioa

Related stories:

For Clean Water: Chlorine-tolerant membranes for desalination
(PhysOrg.com) -- One of the most pressing needs of our time is safe, sustainable access to fresh water. The dominant technology for desalination of water is membrane-based desalination, an energy-efficient, environmentally friendly process. Scientists have now developed a new membrane material that, unlike current polyamide membranes, tolerates chlorinated water.
Swerve left to avoid that satellite
Think you have trouble getting rid of the clutter in your living room? After more than 50 years of launching rockets and satellites into space, the human race now has to deal with the clutter left behind -- or is it "above"? Dead satellites, spent rocket stages, paint flakes, and coolant from nuclear-powered satellites continue to orbit the Earth at ultrahigh velocities.
Self-moisturizing contact lenses, naturally
Even contact lenses are joining the trend to go green. Chemical engineering researchers at McMaster University have shown that a common fluid found in our bodies can be used as a natural moisturizing agent in contact lenses.
Researchers coat titanium with polymer to improve integration of joint replacements
Research at the Georgia Institute of Technology shows that coating a titanium implant with a new biologically inspired material enhances tissue healing, improves bone growth around the implant and strengthens the attachment and integration of the implant to the bone.
Researchers form metal nanoparticles into porous structures
For 5,000 years or so, the only way to shape metal has been to "heat and beat." Even in modern nanotechnology, working with metals involves carving with electron beams or etching with acid.


In 'novel playground,' metals are formed into porous nanostructures
For 5,000 years or so, the only way to shape metal has been to "heat and beat." Even in modern nanotechnology, working with metals involves carving with electron beams or etching with acid.
Nanoparticles aid bone growth
In the first study of its kind, bioengineers and bioscientists at Rice University and Radboud University in Nijmegen, Netherlands, have shown they can grow denser bone tissue by sprinkling stick-like nanoparticles throughout the porous material used to pattern the bone.
Can silver nanoparticles be the key to a more compact laser?
“In random media, multiple scattering and interference reduce the diffusion of light, and in case of extremely strong scattering, photon localization, or Anderson localization of light, is predicted like electrons in glasses,” Katsuhisa Tanaka, a scientist in Kyoto University, tells PhysOrg.com. He and his colleagues are interested in using so-called disordered material to create lasers that could increase our understanding of physics – as well as make the laser creation process simpler.

News discussion:

Physics news