IMEC reports 40 microwatt from micromachined piezoelectric energy harvester

IMEC has fabricated an energy harvester to generate energy from mechanical vibrations by using micromachining technology. The harvester comes together with a model which can be used to optimize the device during design. Output powers up to 40µW were obtained which are in range of the required power for wireless sensor applications.

Energy harvesters, transforming ambient energy into electrical energy, are of great value for situations in which batteries cannot be replaced easily. A typical example is autonomous sensor networks that are spread over large areas or placed in locations that are difficult to access.

Vibration harvesters in general make use of electromagnetic, electrostatic or piezoelectric conversion to generate electrical power. IMEC developed, modeled and characterized a miniaturized vibration harvester based on a piezoelectric transducer.

For an input vibration with a resonance frequency of 1.8kHz and an amplitude of 180nm, a maximum experimental output power of 40µW was measured. This comes well in range of the amounts of power needed by wireless sensor applications, such as the pulse-oxymeter developed earlier by IMEC and IMEC-NL, operating from the Holst Centre in Eindhoven (The Netherlands).

"After the demonstration of a battery-less pulse-oxymeter, which is fully powered by a thermal scavenger, this is another encouraging result which brings us closer to seeing miniaturized scavengers in real-life applications. We believe that first of such devices will see market introduction in 5 years from now and will become mainstream by the end of next decade;" said Bert Gyselinckx, Program Director IMEC-NL in the Holst Centre.

The device consists of a piezoelectric capacitor formed by a Pt electrode, a PZT layer and a top Al electrode. This capacitor is fabricated on a cantilever that supports a mass on its tip. As the harvester is subjected to oscillations, the mass causes the piezoelectric layer to be stretched. By doing so, it induces an electrical power when an electrical load is connected to the device.

To optimize the proposed device concept, a model was generated to estimate the output power for a given design. The output power of the fabricated devices can be maximized by maximizing the quality factor Q (through a low parasitic dissipation) and the coupling between the electrical and mechanical part (GEMC; generalized electromechanical coupling factor).

Source: IMEC

Related stories:

Researchers identify photosynthetic dimmer switch
In a study of the molecular mechanisms by which plants protect themselves from oxidation damage should they absorb too much sunlight during photosynthesis, a team of researchers has discovered a molecular “dimmer switch” that helps control the flow of solar energy moving through the system of light harvesting proteins. This discovery holds important implications for the future design of artificial photosynthesis systems that could provide the world with a sustainable and secure source of energy.
Power from Formic Acid
One of the central challenges of our time is the supply of enough environmentally friendly and resource-efficient energy to our society. In this context, hydrogen technology has taken on increased importance.
RFID testbed measures multiple tags at once and rapidly assesses new antenna designs
Researchers have designed a system capable of simultaneously measuring hundreds of radio frequency identification (RFID) tags and rapidly testing new RFID tag prototypes.
'Smart' power meters herald future of our electricity use
(AP) -- Determined to cut his electricity bill, Darrell Brubaker took the usual steps of raising his air conditioner's thermostat and cooking more on the grill. But the key to maximum savings - as much as 6 percent a month last summer - was his grasp of the state of the electrical grid and his family's willingness to adjust their power usage accordingly.
'Nanomechanical Oscillators' Could Lead to New Class of Computers
More than 50 years ago, a graduate student in Japan conceived the “Parametron,” an electrical circuit that could form the basis for digital computers. The concept ultimately fell flat, but recently a pair of scientists gave new life to the idea, and their work could be a first step toward a nanomechanical computer that is based on mechanical rather than electrical operations.
Heat transfer between materials is focus of new research grant
Managing heat is a major challenge for engineers who work on devices from jet engines to personal electronics to nano-scale transistors.
Researchers Prove Existence of New Basic Element for Electronic Circuits -- 'Memristor'
HP today announced that researchers from HP Labs have proven the existence of what had previously been only theorized as the fourth fundamental circuit element in electrical engineering.
No Power Use in Standby: New Zero-Watt Monitor
Computer monitors in standby mode will soon save far more energy. Fujitsu Siemens Computers has developed the world’s first monitor that requires no electricity at all in idle mode.

News discussion:

Technology news