The researchers, from the University of Southern California and NASA’s Jet Propulsion Laboratory, have published their results in a recent issue of
Applied Physics Letters. They fabricated patterns in the nanotubes such as a staircase structure, cylindrical structures, and square arrays with the laser burning method, which might be used for creating gas and liquid transport channels for various applications.
“While carbon nanotubes possess many exceptional properties which far exceed most known bulk materials, creating controlled nanotube structures has always been a challenge,” co-author Stephen Cronin told
PhysOrg.com. “By overcoming this challenge, our technique enables chemically sensitive fields to take advantage of nanotubes’ exceptional properties and expand their possible applications into new areas.”
The researchers grew the MWNTs in a tube furnace heated to 650 degrees Celsius. Then they focused a high-powered 532-nm laser through a microscope onto the densely packed vertical nanotubes, burning some of the nanotubes to create the desired pattern. Burnout occurred in less than a second at an estimated temperature of around 800 degrees Celsius in air. The researchers found that burnout required a minimum laser power of 244 microwatts, and they tested the method with laser powers up to 9,000 microwatts.
“The initial burnout we observed came as quite a surprise and appeared very striking in our microscope images,” Cronin said. “Typically, carbon nanotubes lying on a silicon wafer are very difficult to heat with a laser.”
Until now, most attempts at patterning microstructures have been done with conventional lithography or other techniques. However, lithography is limited to 2D structures and leaves chemical residues that would be incompatible with biological applications. Other methods don’t use nanotubes as the medium, and so cannot take advantage of nanotubes’ desirable properties, such as mechanical strength, high surface area, and electrical and thermal conductivities.
Laser burnout seems to offer a good solution, as it’s quick, doesn’t involve chemicals, and the resolution is limited primarily by the spot size of the objective lens. Using Raman spectroscopy, a non-contact method for measuring the wavelength and intensity of scattered light, the researchers could determine the depth of the burn. This testing revealed that burnout depth increased with laser power, and the minimum burnout depth was 5 micrometers, which could be decreased further with the use of a higher numerical aperture microscope lens.
The researchers also noticed an interesting phenomenon that occurred after laser treatment, which was the development of white spots ranging in size from 100 to 200 nm on the top of the MWNT forests. A scanning electron microscope revealed that the white spots were nanotube bundles that aggregate during the burnout process, providing some insight into the dynamics of the process.
The researchers hope to use the technique to create well-defined gas and liquid transport channels as well as deep trenches for superhydrophobic microfluidic channels. The checker board-like arrays may also be suitable for field emission applications. Further, the researchers suggest that the method may serve as a basis for developing similar patterning methods in other material systems.
“Potential applications are on-chip DNA manipulation, chemical and protein identification, templates for directed stem cell growth, and gas mixture separation,” said Cronin.
Citation: Hung, Wei Hsuan, Kumar, Rajay, Bushmaker, Adam, Cronin, Stephen B., and Bronikowski, Michael J. “Rapid prototyping of three-dimensional microstructures from multiwalled carbon nanotubes.”
Applied Physics Letters 91, 093121 (2007).
Copyright 2007 PhysOrg.com.
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part without the express written permission of PhysOrg.com.
Related stories:
A fine-tooth comb to measure the accelerating universe
Astronomical instruments needed to answer crucial questions, such as the search for Earth-like planets or the way the Universe expands, have come a step closer with the first demonstration at the telescope of a new calibration system for precise spectrographs. The method uses a Nobel Prize-winning technology called a 'laser frequency comb', and is published in this week's issue of
Science.
Putting the Squeeze on Nitrogen for High Energy Materials
(PhysOrg.com) -- Nitrogen atoms like to travel in pairs, hooked together by one of the strongest chemical bonds in nature. By subjecting nitrogen molecules to extreme temperatures and pressures scientists are getting a new understanding of not only nitrogen but other similar molecules, including hydrogen. In the current online edition of
Physical Review Letters, researchers from the Carnegie Institution's Geophysical Laboratory report changes in the melting temperature of solid nitrogen at pressures up to 120 gigapascals (more than a million atmospheres) and temperatures reaching 2,500° Kelvin (more than 4000° Fahrenheit).
OU researchers developing new tool to detect cancer
Early cancer detection can significantly improve survival rates. Current diagnostic tests often fail to detect cancer in the earliest stages and at the same time expose a patient to the harmful effects of radiation. Led by Dr. Patrick McCann, a small group of internationally known researchers at the University of Oklahoma with expertise in the development of mid-infrared lasers is working to create a sensor to detect biomarker gases exhaled in the breath of a person with cancer.
Life under the laser
Researchers at The University of Nottingham have developed a unique technology that will allow scientists to look at microscopic activity within the body's chemical messenger system for the very first time, live as it happens.
Engineering new uses for gold
The glitter of gold may hold more than just beauty, or so says a team of MIT researchers that is working on ways to use tiny gold rods to fight cancer, deliver drugs and more.
An Unconventional Metal
The semiconductor silicon and the ferromagnet iron are the basis for much of mankind's technology, used in everything from computers to electric motors. In this week's issue of the journal
Nature (August 21st) an international group of scientists, including academic and industrial researchers from the UK, USA and Lesotho, report that they have combined these elements with a small amount of another common metal, manganese, to create a new material which is neither a magnet nor an ordinary semiconductor.
Fast quantum computer building block created
(PhysOrg.com) -- The fastest quantum computer bit that exploits the main advantage of the qubit over the conventional bit has been demonstrated by researchers at University of Michigan, U.S. Naval Research Laboratory and the University of California at San Diego.
Light touch: Controlling the behavior of quantum dots
Researchers from the National Institute of Standards and Technology and the Joint Quantum Institute (JQI), a collaborative center of the University of Maryland and NIST, have reported a new way to fine-tune the light coming from quantum dots by manipulating them with pairs of lasers. Their technique, published in
Physical Review Letters, could significantly improve quantum dots as a source of pairs of “entangled” photons, a property with important applications in quantum information technologies.
