Titania nanotubes make better solar cells

"Solar cell technology has not changed very much over time and is still predominantly silicon solar cells," says Dr. Craig Grimes, professor of electrical engineering and materials science and engineering. "It takes a great deal of energy, 5 gigajoules per square meter, to make silicon solar cells. It can be argued that silicon solar cells never fully recover the energy it takes to make them in the first place."

The new focus in solar cells is toward dye sensitive solar cells, which have been made using nanoparticles and a variety of dyes.

"Nanoparticle solar cells are the gold standard of this new approach," says Grimes. "However, because of limitations, it appears they have gotten as good as they are going to get."

The researchers are instead looking at titania nanotubes to replace the particulate coatings in dye sensitive solar cells and, their initial attempt produced about 3 percent conversion of solar energy to electricity, they report in today's issue of Nano Letters. The researcher's inability to grow longer titania nanotubes, constrained the solar conversion rate.

"I think we can reach a 15 percent conversion rate with these cells, and other researchers do as well," says Grimes. "That is 15 percent with a relatively easy fabrication system that is commercially viable."

Conventional solar cells are made from blocks of slowly made silicon boules that are sliced into wafers. Grimes and his team use an easier approach. They coat a piece of glass with a fluorine-doped tin oxide and then sputter on a layer of titanium. The researchers can currently lay down a 500-nanometer thick titanium layer. They then anodize the layer by placing it in an acidic bath with a mild electric current and titanium dioxide nanotube arrays grow to about 360 nanometers. The tubes are then heated in oxygen so that they crystalize. The process turns the opaque coating of titanium into a transparent coating of nanotubes.

This nanotube array is then coated in a commercially available dye. The dye-coated nanotubes make up the negative electrode and a positive electrode seals the cell which contains an iodized electrolyte. When sun shines through the glass, the energy falls on the dye molecules and an electron is freed. If this electron and others make their way out of the tube to the negative electrode, a current flows. Many electrons do not and are recombined, but the tube structure of the titanium dioxide allows an order of magnitude more electrons to make it to the electrode than with particulate coatings.

"There is still a great deal of optimization of the design that needs to be done," says Grimes. "Now, with the help of the Pennsylvania Energy Development Authority, we will have equipment to make high quality titanium coatings that are thicker. If we get about 3 percent conversion with 360 nanometers, what we could get with 4 microns is an exciting question we soon hope to answer."

The thickness of the titanium layer constrains the height of the nanotubes. With thicker initial coatings, longer tubes would produce more electrons that do not recombine, producing more electricity.

Other aspects of the titania nanotube dye sensitive solar cells that need to be optimized include the thickness of the cells. Currently, spacers separate the two layers and provide internal support. These spacers are 25 microns thick. If the spacers could be made as sturdy, but shorter, there would be less of a distance for the electrons to travel and more electrons will make it across the electrodes.

Source: Penn State

Breakthrough in efficiency for dye-sensitized solar cells
In a paper published in the journal Nature Materials, EPFL professor Michael Graetzel, Shaik Zakeeruddin and colleagues from the Changchun Institute of Applied Chemistry at the Chinese Academy of Sciences have achieved a record light conversion efficiency of 8.2% in solvent-free dye-sensitized solar cells.
Researchers make breakthrough in renewable energy materials
University of Queensland researchers have made a ground-breaking discovery that produces highly efficient miniature crystals which could revolutionise the way we harvest and use solar energy.
Popcorn-ball design doubles efficiency of dye-sensitized solar cells
A new approach creates a dramatic improvement in cheap solar cells now being developed in laboratories.
The future of solar-powered houses is clear
The future of solar-powered houses is clear. People could live in glass houses and look at the world through rose-tinted windows while reducing their carbon emissions by 50 percent thanks to QUT Institute of Sustainable Resources research.
Substantial improvement in essential cheap solar cell process
A cheap alternative to silicon solar cells can be found in dye-sensitised solar cells. This type of cell imitates the natural conversion of sunlight into energy by, for instance, plants and light-sensitive bacteria. Annemarie Huijser has succeeded in substantially improving a process in this type of solar cell, which is similar to Grätzel cells. Huijser will receive her PhD on this subject from TU Delft on Tuesday 25 March.
Quantum Dots May Lead to Rainbow Solar Cell
For the first time, researchers have created solar cells made of different-sized quantum dots, each tuned to a specific wavelength of light. By arranging these quantum dots in an ordered pattern, the scientists hope that they can one day fabricate “rainbow” solar cells, which can efficiently harvest a large part of the useful spectrum of sunlight.
Capturing Sunlight: Indoline Dyes Improve Efficiency of Solar Cells
Solar cell technology is marching ahead, though it still struggles with the two problems: efficiency and high production costs. In collaboration with Satoshi Uchida at the University of Tokyo, Michael Grätzel and his research group at the Swiss Federal Institute of Technology in Lausanne have now developed new sensitizers that should help an inexpensive type of solar cell to be more efficient. As they report in the journal Angewandte Chemie, the sensitizers are based on the dye indoline.
Solar cell directly splits water for hydrogen
Plants trees and algae do it. Even some bacteria and moss do it, but scientists have had a difficult time developing methods to turn sunlight into useful fuel. Now, Penn State researchers have a proof-of-concept device that can split water and produce recoverable hydrogen.

Titania nanotubes make better solar cells

Related stories:

News discussion: