Soldered lenses

Lenses in optical devices are kept in place by adhesives. This can cause problems when the microscopes and cameras are employed inside a vacuum, as the adhesives may release gases that contaminate the lenses. One alternative is to solder them instead.

When cameras and microscopes are placed in a vacuum, their functionality can be seriously impaired. This is because their lenses and prisms are normally fixed with adhesives, which release gases inside the vacuum. The gas molecules settle on the lenses and alter their optical properties. At high temperatures, too, or when using lasers in the UV range, the adhesives cause problems: They become soft or brittle, and the optical components can slip by several micrometers.

Researchers at the Fraunhofer Institute for Applied Optics and Precision Engineering IOF in Jena have now developed an alternative in a joint project with engineers from Pac Tech GmbH in Nauen. “We solder the optical components instead of gluing them,” says IOF group manager Dr.-Ing. Erik Beckert. “This has a definite advantage: The solder material is resistant to extreme temperatures and radiation, and also conducts heat and electricity.”

To enable them to apply the solder to the lenses just as flexibly as an adhesive, the researchers adapted the ‘solder bumping’ technique normally used in electronics manufacture. Small balls of solder contained in a dosing head slip one by one into a capillary, where a laser beam heats them until they become liquid. The liquid solder droplets are then shot by a nitrogen pressure pulse to the spot where they are needed to fix the lens. Once in place, the solder cools in just a few milliseconds and solidifies.

“This process can be automated and is very flexible. We can apply the solder downwards or from various other angles and in places that are difficult to access,” says Beckert. Solder bumping is much faster than gluing. While it takes 10 to 30 seconds to apply an adhesive and let it harden, soldering takes less than one second. To ensure that the solder does not come off the glass lenses, they have to be metallized in advance, for instance in a sputtering process which can be carried out on a large scale.

A special feature of the solder bumping process is that it does not need a fluxing agent. “Normally, flux is used to ensure that the solder fully coats the metal. However, in a vacuum, the flux residues would outgas in a similar way to adhesives. The lens system would have to be thoroughly cleaned before being used. That’s not necessary with the flux-free version,” says Beckert.

At Optatec, which will take place in Frankfurt (Germany) on June 17 through 20, the researchers will present prototypes of optical components fixed in place by solder bumping. Beckert hopes that the system will be ready for use in production in a year or two’s time.

Source: Fraunhofer-Gesellschaft

Related stories:

IBM researchers unveil green optical network technology prototype
IBM researchers today unveiled the fastest and most highly integrated optical data bus ever developed. The prototype technology could bring massive amounts of bandwidth in an energy-efficient way to all kinds of machines—from cell phones to supercomputers. This could revolutionize the way we access, use and share information across many different applications.
Precision bonding makes tiny high performance actuators possible
Using a new precision bonding process they developed, Penn State researchers have designed and fabricated tiny new piezoelectric microactuators -- the largest only a hair's breadth wide -- based on coupling commercially available materials with existing micromachining technology.
Molecular wires and corrosion control boost performance of conductive adhesives
Replacing lead-based solder

Electrically conductive adhesive (ECA) materials offer the electronics industry an alternative to the tin-lead solder now used for connecting display driver chips, memory chips and other devices to circuit boards. But before these materials find broad application in high-end electronic equipment, researchers will have to overcome technical challenges that include low current density.
Closing the Loop: Georgia Tech Researchers Develop New Data-driven Closed-loop control for stencil printers
In electronics assembly, 60 to 70 percent of final defects occur during the stencil printing process (SPP), a stage of surface-mount technology for printed circuit board assembly.

To address this problem, engineers at Georgia Tech’s Center for Board Assembly Research (CBAR) have developed a new data-driven, closed-loop control technology that adjusts equipment parameters in real time, resulting in fewer defects and higher yields.
Parallel 'nano-soldering' technique chosen for year's top-50 by Nanotech Briefs
(PhysOrg.com) -- You should have so much patience to solder nanowires to nanoelectrodes. Talk about fine work. That’s why a new electroplating process that simultaneously joins many silicon nanowires to many prepatterned electrodes was selected for a 2008 Nano 50 Award by Nanotech Briefs.
Lead shot and sinkers: Weighty implications for fish and wildlife health
Millions of pounds of lead used in hunting, fishing and shooting sports wind up in the environment each year and can threaten or kill wildlife, according to a new scientific report.
Researchers design copper connections for high-speed computing
As computers become more complex, the demand increases for more connections between computer chips and external circuitry such as a motherboard or wireless card. And as the integrated circuits become more advanced, maximizing their performance requires better connections that operate at higher frequencies with less loss.
Laser joining of solar cells
A single solar cell produces a relatively low output – it’s a case of strength in numbers. Tiny strips of metal are used to link cells together. If the laser soldering temperature is too high, the solder joint may fracture. A new system provides automatic temperature regulation.

News discussion:

Technology news