The NIST nanomechanical mapper uses custom software and electronics to process data acquired by a conventional atomic force microscope (AFM), transforming the microscope’s normal topographical maps of surfaces into precise two-dimensional representations of mechanical properties near the surface.
The images enable scientists to see variations in elasticity, adhesion or friction, which may vary in different materials even after they are mixed together. The NIST system, described fully for the first time in a new paper, can make an image in minutes whereas competing systems might take an entire day.
The images are based on measurements and interpretations of changes in frequency as a vibrating AFM tip scans a surface. Such measurements have commonly been made at stationary positions, but until now 2D imaging at many points across a sample has been too slow to be practical.
The NIST DSP-RTS system (for digital signal processor-based resonance tracking system) has the special feature of locking onto and tracking changes in frequency as the tip moves over a surface. Mechanical properties of a sample are deduced from calculations based on measurements of the vibrational frequencies of the AFM tip in the air and changes in frequency when the tip contacts the material surface.
NIST materials researchers have used the system to map elastic properties of thin films with finer spatial resolution than is possible with other tools. The DSP-RTS can produce a 256 × 256 pixel image with micrometer-scale dimensions in 20 to 25 minutes. The new system also is modular and offers greater flexibility than competing approaches. Adding capability to map additional materials properties can be as simple as updating the software.
Citation: A.B. Kos and D.C. Hurley. Nanomechanical mapping with resonance tracking scanned probe microscope. Measurement Science and Technology 19 (2008) 015504.
Source: National Institute of Standards and Technology
Related stories:
NIST/NIH micromagnets show promise as colorful 'smart tags' for magnetic resonance imaging
Colo.-Customized microscopic magnets that might one day be injected into the body could add color to magnetic resonance imaging (MRI), while also potentially enhancing sensitivity and the amount of information provided by images, researchers at the National Institute of Standards and Technology (NIST) and National Institutes of Health (NIH) report. The new micromagnets also could act as "smart tags" identifying particular cells, tissues, or physiological conditions, for medical research or diagnostic purposes.
Disorder Enables Extreme Sensitivity in Piezoelectric Materials
A research team working at the National Institute of Standards and Technology has found an explanation for the extreme sensitivity to mechanical pressure or voltage of a special class of solid materials called relaxors. The ability to control and tailor this sensitivity would allow industry to enhance a range of devices used in medical ultrasound imaging, loudspeakers, sonar and computer hard drives.
Improved Ion Mobility Is Key to New Hydrogen Storage Compound
A materials scientist at the National Institute of Standards and Technology has deciphered the structure of a new class of materials that can store relatively large quantities of hydrogen within its crystal structure for later release. The new analysis may point to a practical hydrogen storage material for automobile fuel cells and similar applications.
Spin Control: New Technique Sorts Nanotubes by Length
Researchers at the National Institute of Standards and Technology (NIST) have reported a new technique to sort batches of carbon nanotubes by length using high-speed centrifuges. Many potential applications for carbon nanotubes depend on the lengths of these microscopic cylinders, and one of the most important features of the new technique, say the scientists, is that it should be easily scalable to produce industrial quantities of high-quality nanotubes.
Possible Mechanism for Enormous Electromechanical Response
Scientists at the U.S. Department of Energy's Brookhaven National Laboratory and collaborators at Stony Brook University, Johns Hopkins University, and the National Institute of Standards and Technology have discovered that nanosized regions with local polarizations, or "electric dipoles," in a special class of otherwise disordered materials may underlie these materials' extreme electromechanical response to an external electric field or physical deformation.
New 3-D Test Method for Biomaterials 'Flat Out' Faster
A novel, three-dimensional (3-D) screening method for analyzing interactions between cells and new biomaterials could cut initial search times by more than half, researchers from the National Institute of Standards and Technology (NIST) and Rutgers University report in the new issue of
Advanced Materials.
Carbon Nanotube Measurements: Latest in NIST 'How-To' Series
The National Institute of Standards and Technology, in collaboration with the National Aeronautics and Space Administration, has published detailed guidelines for making essential measurements on samples of single-walled carbon nanotubes (SWCNTs). The new guide constitutes the current “best practices” for characterizing one of the most promising and heavily studied of the new generation of nanoscale materials.
Researchers pave the way for anthrax spore standards
Researchers from the National Institute of Standards and Technology (NIST) and the U.S. Army Dugway (Utah) Proving Ground have developed reliable methods based on DNA analysis to assess the concentration and viability of anthrax spores after prolonged storage. The techniques and data are essential steps in developing a reliable reference standard for anthrax detection and decontamination.
